The post 1743B appeared first on RN Embedded Solutions.

• Three independent outputs
• Independent control knobs for voltage and current settings of variable outputs
• CV (constant voltage) and CC (constant current) operation
• Separate 3-digit voltage and current displays for variable outputs
• LED indication for CV and CC modes
• Overload indication LED for fixed output
• Series tracking and parallel tracking mode operation
• Output terminals are banana style (not binding posts), click on Accessories for leads
• Model 1673 B&K Precision

The post 1673 appeared first on RN Embedded Solutions.

These power supplies offer SCPI IEEE488.2 compliant USB (standard), RS232, RS485, GPIB and LAN interfaces, combined with front and rear panel output and remote sense terminals to facilitate test system development and integration. The LAN interface includes a built-in web server that allows users to configure, control, or monitor basic power supply settings.

In addition to a full numerical keypad for convenient data entry, this series also provides unique features not typically found in comparable power sources, such as LED test modes, modular interface card slots, automatic range selection, and an optional 8-bit bidirectional digital I/O interface.

• Single and dual output models with up to 210W output power
• Exceptionally low ripple and noise
• Front and rear panel output
• List mode for executing up to 10 stored test sequences with a maximum of 150 steps in total
• Overvoltage/overcurrent/overtemperature protection (OVP/OCP/OTP) and key-lock function
• Fast transient response time of < 50 us for most models
• Fast command processing time < 10 ms
• Programmable voltage and current slew rates
• Standard USB interface
• 4 optional types of modular interface cards add LAN and GPIB, Digital I/O and Analog Control, RS485, or RS232 functionality
• LabVIEW (TM) drivers available
• Model 9183B B&K Precision

The post 9183B appeared first on RN Embedded Solutions.

For remote control, the standard USB (USBTMC-compliant) and RS232 interfaces supporting SCPI commands can be used to remotely control the power supplies via a PC.

• Three independent and electrically isolated outputs
• Displays voltage and current settings for all three channels simultaneously
• Low noise, linear regulation
• High programming and readback resolution of 1 mV / 1 mA
• Series and parallel modes combine channels to increase the output voltage or current
• Tracking mode allows users to set up channels to maintain a programmed ratio
• Fully programmable channels with Output On/Off control
• Store and recall up to 36 instrument settings
• Remote sense
• Timer-controlled output function adjustable from 0.1 – 99999.9 s
• Standard USB (USBTMC-compliant) and RS232 interfaces supporting SCPI commands for remote control
• NI certified LabVIEW driver and softpanel for remote control, test sequence generation, and datalogging available
• Overvoltage (OVP) and overtemperature (OTP) protection including keylock function
• Compact 19” half-rack form factor allows for side-by-side rack mounting of two units
• Model 9131C B&K Precision

The post 9131C appeared first on RN Embedded Solutions.

The AC source provides a power line disturbance (PLD) simulator, list mode, and sweep mode for simulation of common power grid faults and disturbances. A built-in dimmer function is also available for testing motors and LEDs.

• 0 to 300 V, low distortion AC power source with models delivering a maximum of 1500 VA, 12 Arms / 48 Apeak
• Output frequency adjustable from 45 Hz – 500 Hz
• Select 150 V / 300 V autoranging or 300 V range operation for continuous sweep from 0 – 300 V
• Displays Vrms, Irms, Ipeak, frequency, PF, apparent power, true power, and elapsed output time
• Adjustable phase angle control
• Built-in PLD and dimmer simulation
• Voltage and frequency sweep mode
• Downloadable LabVIEW driver and soft panel software for remote control
• Standard USB (USBTMC-compliant), RS232, and LAN interfaces
• GPIB optional on select models
• Pre-compliance testing for voltage dips and frequency simulation according to IEC61000-4-11 / 4-14 / 4-28
• Model 9803B B&K Precision

Common applications

The 9800/B series of AC power source is suitable for evaluating transformers, TRIACs, SCRs, and passive components as well as production, R&D, service, and pre-compliance testing.

The post Model 9803B appeared first on RN Embedded Solutions.

The AC source provides a power line disturbance (PLD) simulator, list mode, and sweep mode for simulation of common power grid faults and disturbances. A built-in dimmer function is also available for testing motors and LEDs.

• 0 to 300 V, low distortion AC power source with models delivering a maximum of 1500 VA, 12 Arms / 48 Apeak
• Output frequency adjustable from 45 Hz – 500 Hz
• Select 150 V / 300 V autoranging or 300 V range operation for continuous sweep from 0 – 300 V
• Displays Vrms, Irms, Ipeak, frequency, PF, apparent power, true power, and elapsed output time
• Adjustable phase angle control
• Built-in PLD and dimmer simulation
• Voltage and frequency sweep mode
• Downloadable LabVIEW driver and soft panel software for remote control
• Standard USB (USBTMC-compliant), RS232, and LAN interfaces
• GPIB optional on select models
• Pre-compliance testing for voltage dips and frequency simulation according to IEC61000-4-11 / 4-14 / 4-28
• Model 9803 B&K Precision

Common applications

The 9800/B series of AC power source is suitable for evaluating transformers, TRIACs, SCRs, and passive components as well as production, R&D, service, and pre-compliance testing.

The post Model 9803 appeared first on RN Embedded Solutions.